AV Senders and IR Remote Extenders

Coaxial HD Video Streamer with IR Remote Extender
		INVACOM
		F807508
		–
		tvLinkHD Wired System
		The tvLinkHD Wired System enables reliable
		streaming of live and stored HD content from a
		STB/DVD over coax, max distance 150m with full
		remote control functionality.
		–
		Stream live HD content from any HD device via a
		traditional coaxial distribution system
		• Multiple viewing receivers can be connected to one
		transmitter
		• Full IR Remote control of HD source device
		• Ideal for homes, pubs & clubs
		• Can use the same coax as existing DTT/Sat services
		• HDCP & WPA2 AES Content protection
		• Up to 150m range

		INVACOM
		F807516
		–
		tvLINKHD Multi-Point Receiver
		Expand your HD system by adding further receivers.
		A 5-2400MHz Wideband DC passing Splitter is needed
		in order for you to achieve this.
		–
		Additional receiver so you can expand your HD system
		to multiple locations in your home up to a maximum of
		4 receivers.
		The kit comes with the receiving unit, wall and shelf
		mounting and instruction guide.

AV LINKS
	GECEN
	GC-2G4B
	–
	2.4GHz wireless A/V Sender with four selectable channels
	433.92MHz infrared radio-control return feature
	Antenna (2.4GHz) is embedded into housing
	Compatible with camcorder and CMOS camera application
	Low power consumption
	Supports video transmission of NTSC or PAL and
	stereo audio transmission
	Equipment realizes that several televisions share one
	set-top box or DVD
	Transmission distance up to 100 meters under unobstructed
	circumstance
	Ideal for microwave anti-jamming capability
	Supply Voltage: 9V

	TEKMEDIA
	65020001
	–
	Wireless A/V Sender
	Easy to install
	Long carrier
	No interference with mobiles
	Antenna (2.4GHz) is embedded into housing
	Compatible with DVD, VCR, camcorder, computer, etc.
	High AV signal quality
	Supports video transmission of NTSC or PAL and stereo
	audio transmission
	Supply Voltage: 12V

IR REMOTE EXTENDERS
	Ebode
	IRLPKUK – IR Link P
	WIRE
	–
	Description
	The ebode IR Link P is an InfraRed extender system that allows full
	InfraRed remote control operation of A/V components located behind
	closed cabinet doors or other concealed and/or out-of-sight locations.
	The ebode IR Link P uses power from the mains (no battery required).
	An InfraRed Extender in general consists of an IR (InfraRed) capture
–	device, the Receiver, a distribution circuit/connecting block, the Hub,
	and finally the IR LED output, the Emitter, which flashes the IR signal
	to the A/V component.
	–
	Set content
	The ebode IR Link P consists of 3 parts:
	1x IR Receiver IRLP TRX
	1x IRHUB1 with attached IR Emitters and extra 3.5mm jack for
	Emitter expansion
	1x 12VDC Power supply wall adapter


	Ebode
	IRLCKUK – IR Link C
	COAX
	–
	Description
	The IR Link C is a mains powered InfraRed Extender System that
	allows full remote control operation of audio/video components (such
	as your Blu-ray player, A/V Receiver, DVR, Satellite Box, Cable Tuner,
	etc.) which are located in another room and makes use of existing
	coax cable (CATV).
	An InfraRed Extender in general consists of an IR (InfraRed) capture
	device, the Receiver, a distribution circuit/connecting block, the Hub,
	and finally the IR LED output, the Emitter, which flashes the IR signal
	to the A/V component.
	–
	Set content
	The ebode IR Link C consists of the following supplied parts:
	1. One InfraRed Receiver, Model IRLP. It is placed at the remote room
	location to receive IR signals from the handheld remote controller.
	2. One INJ Injector. This unit, located in the remote room, injects the
	remote control signal into the room to- room coaxial cable (along with
	the TV signal) and passes it to the CPL Coupler in the main room. It
	also provides quick connection of the IRLP IR Receiver and 12VDC
	power supply cables.
	3. One CPL Coupler. Located in the main room, this Coupler extracts
	the remote control signal from the coaxial cable and passes it to the
	emitters that control your source equipment.
	4. One Triple Blinking IR Emitter, model 3IREDB. The Emitters on this
	device allow control of three InfraRed remote controlled audio/video
	components. The IR Emitters have a self adhesive film on one surface
	of each Emitter. This allows them to be “stuck” to the IR sensor
	“window” on your source equipment. There is a set of replacement
	adhesive pads included.
	5. A 12VDC Power Supply. This plugs into a 230V~50Hz outlet to
	provide power to the IRLP Receiver.
	6. 3 extra replacement adhesives for the IR Emitters
	–
	Optional:
	IRLCEXPUK
	EXTRA INJ Injector kit for IRLCKUK – IR Link C
	–
	Set content
	1x table top mouse receiver
	1x RF/IR injector
	1x power supply

	*Optional:*
	3IREDB
	Extra 3IREDB Triple Infrared Emitting Diode Blinking/Flash
	Triple infrared emmitting diode blinking. For connecting to CPL
	Coupler to control 3 more sources (total 6 sources).
	–
	The IRED Emitter contains three tiny infrared LED’s* housed in a
	miniature, mouse shaped, black appearing, injection molded plastic
	shell. It emits IR (infrared) control signals sent to it by IR receivers or
	other controllers. The IRED can be installed directly on the IR sensor
	window of the controlled device or other suitable location.
	LED = Light Emitting Diode


	Ebode
	PM28UK
	WIRELESS
	–
	Description
	PowerMid Premium, Extend the signal of your remote control through
	walls and ceilings
	–
	This kit allows you to control remotely any A/V distant appliance, TV,
	VCR, Hi-Fi, satellite and cable box, just by using your existing remote
	control! The remote control signal is transmitted through walls and
	ceilings, up to 100 meters away (open field, about 30 meters through
	walls and ceilings).
	–
	The ebode proprietary eIR2xTM (pronounce Irex) Technology
	guarantees a high level of immunity for infrared noise of direct
	sunlight, CFL lighting and Flat Panel TV’s (including Plasma, LCD and
	LED). Provides accurate reproduction of the latest generation
	Infrared codes that are used in remote controls of, for instance,
	set-top boxes and media players (incl. RC5/6, RCMM, XMP).
	–
	Set Content
	1x Transmitter: converts IR signals of remote controls into 433.92MHz
	RF messages and transmits them to the Receiver, even through walls
	and ceilings
	1x Receiver: converts RF messages back into IR signals to control the
	selected A/V source
	2x Mains power supply wall adapters 230V~50Hz to 9VDC 200mA
	–
	Technical data
	Power: SMPS AC/DC adapter 100-240V~50Hz – 12VDC 200mA (UK)
	Frequency Band: 433.92 MHz
	RF Output Power: 1mW typical @3m
	Operating Range: 100m* (open field). 15-30m* (in building)
	*depending on environmental conditions
	Dimensions: 56 x 40 x 25 mm
	25 mm is height without antenna, height including antenna is 50 mm.
	–
	Optional:
	• ST28UK
	Extra Transmitter for PowerMid Premium (PM28UK)
	Add EXTRA ST28 Transmitters to use your remote controls in several
	rooms
	–
	*Optional:*
	3IREDB
	Extra 3IREDB Triple Infrared Emitting Diode Blinking/Flash
	Triple infrared emmitting diode blinking. For connecting to PM28
	Receiver to control more sources.
	–
	Add a 3IREDB Infrared Extender if you need to place the PowerMid
	Receiver next to your equipment instead of in front of it, or if your
	equipment is located inside a closed cabinet
	–
	The IRED Emitter contains three tiny infrared LED’s* housed in a
	miniature, mouse shaped, black appearing, injection molded plastic
	shell. It emits IR (infrared) control signals sent to it by IR receivers or
	other controllers. The IRED can be installed directly on the IR sensor
	window of the controlled device or other suitable location.
	LED = Light Emitting Diode


	LEM
	MX400S (Stereo RF Modulator with IR Remote Extender)
	–
	Modulator section
	Full band DSB Modulator Double Scart connector
	Selectable TV standards
	Output channels/frequency range: Audio stereo Hi-Fi
	I-IF 38,9 MHz
	VHF E2…E12
	CATV S2…S10 / S11…S20
	HYPER S21…S38
	UHF 21…70
	Selection of the output ch. by dip-switch
	PLL quarz crystal oscillator
	Preserves Dolby Digital Sorround
	Audio with Automatic Control Gain
	Built-in power supply
	Harmonics filter suppressor
	Permits the mixing of the Terr. and SAT
	Loop through RF combining
	Attractive ABS box
	Connectors: video/audio – type scart in-scart out sockets, RF-F type
	RF output level (typical) /impedance 90 dBμV adjustable 0/-25 dB
	Built-in test pattern generator
	–
	IR Remote extender section
	Code programmable by dip-switch
	Compatible with most type of remote control
	External miniaturized IR transmitting and receiving sensors
	Plasma and Lcd proof sensor
	Crystal controlled 433 Mhz transmitter
	Adjustable telescopic antenna
	RF link test
	–
	Option:
	infrared receiver MSR100 may be added to extend remote
	control to each room required

	TECHNOMATE
	TM-IR
	–
	Transmits remote control signal with radio frequency
	Operating Frequency: 433.92MHz
	Transmission distance up to 100 meters under unobstructed
	circumstance
	Low power consumption
	Supply Voltage: DC 18V

	GECEN
	GC-IR04
	–
	Transmits remote control signal with radio frequency
	Operating Frequency: 433.92MHz
	Transmission distance up to 60 meters under unobstructed
	circumstance
	Low power consumption
	Supply Voltage: DC 15V

	GECEN
	GC-IR02
	–
	Transmit the remote control signal with radio frequency
	By installing the transmitter in the battery pocket only
	Operating Frequency: 433.92MHz
	Uses the smartest and easiest technology in extending the
	remote control operation
	Transmission distance up to 30 meters
	Supply Voltage: 12V
	–
	Optional extra parts:
	– RF Transmitter
	– Rechargeable 2/3AAA Battery
	– AAA to AA Battery Adapter Sleeve
	–
	–

	GECEN
	GC-IR02C
	–
	IR Remote Extender with FSK Modulation/Demodulation
	Carrier Frequency: 38KHz
	Application: home cable TV network
	Signal can pass through several splitters or couplers
	Suitable for RF transmission
	Supply Voltage: 9V

		Televes
		7237
		–
		Transmits remote control signal with radio frequency
		Operating Frequency: 433.92MHz
		Transmission distance up to 100 meters under
		unobstructed circumstance
		Low power consumption
		Supply Voltage: 17V
		–
		Option:
		7219
		Extra Transmitter for 7237 set can be be added to
		extend remote control to each room required

	Televes
	7605
	–
	IR Remote Extender with Modulation/Demodulation
	Can control 2 source devices
	Carrier Frequency: 36KHz (RC5)
	Modulation Frequency: 14.7KHz
	Application: home cable TV network
	Signal can pass through several splitters or couplers
	Suitable for RF transmission
	Supply Voltage: 12V
	–
	Option:
	7606
	–
	Extra Transmitter for 7605 set can be be added to extend
	remote control to each room required